How To Install Composite Decking Over Concrete Steps
How To Build a Deck Over An Ugly Cement Stoop
If like us, you lot have an quondam concrete stoop that has more seen improve days, rather than going through the hassle of tearing it out, why not requite it a facelift? From concrete stains and epoxy coatings to a diverseness of enclosures, there are several ways to go near this. We chose a composite decking surround as we liked the low-maintenance factor and forest look. Read on for details on how we transformed our old, crude concrete stoop into a beautiful backdoor landing, and make sure to cheque out my helpful hints at the bottom!
What You lot Need
- 4 1" x half dozen" solid composite decking @ xvi' long. We used NewTechWood, Cortes Series in Peruvian Teak
- 3 2" x four" treated lumber @ eight' long
- Two 2" x ii" treated lumber @ viii' long
- Two 1" x half dozen" treated lumber @ 8' long
- 2.v" Galvanized screws
- ii" Galvanized trim head screws
- Mitre saw
- Tabular array saw
- Round saw (optional)
- Level
- Cordless drill
- Quart of outside paint to lucifer exterior dwelling color
- Foam paint castor
- Speed square
- Pencil
- Large all-purpose nails for board spacing
- Shims
i. Create a rectangular frame of ii" x 4" treated lumber around the top perimeter of your stoop. Apply a circular saw to brand these cuts.
So utilise a cordless drill to bury two.5" galvanized screws at an angle to connect the boards to i another.
2. Adjacent add every bit spaced 2" x ii" supports inside the perimeter of the frame.
Attach to the larger frame with angled ii.5″ galvanized screws.
iii. Calculate your desired overhang. Nosotros found it easiest to visualize if we physically laid a deckboard on the edge of the stoop. Make sure to account for the thickness of the riser board when computing the overhang.
So, if your riser board is 1" thick, and y'all'd similar the overhang to be 1.five", measure 2.5" out from the front of the stoop, and this will be the longest point of your mitre cut.
4. Measure and mitre cutting the left and correct "border" boards first. Then cutting the front end "border" board with a mitre cutting at each finish. Use ii″ small-head galvanized screws to attach the "border" to the frame.
five. Side by side, depending on how much or little the deck boards overhang, you may need to add 2" ten 4" framing boards for additional deck board support. Install these the same way you installed the ii" x 2" supports in Stride 2.
6. Now it's fourth dimension to add in the horizontal deck boards! Use a mitre or circular saw to square cut the boards downwards to the correct width, and space them out using large all-purpose nails.
Tip: One time y'all have the boards laid out on the stoop, I'd highly recommend pre-drilling holes for the screws, as you'll avoid a mushrooming result effectually each screw. Double check the placement of your 2" x 2" framing supports, before drilling.
7. And then add your 2" screws in the pre-drilled holes to secure the boards into identify.
8. At this betoken, the meridian of the stoop is complete, and all that'southward left is the riser! Nosotros painted our riser to match the color of our business firm, as a way to break up the brown of the stoop acme and the patio pavers below. You lot can either choose to paint treated lumber to match an existing element on your home, or continue with the blended decking for the riser.
ix. Measure and cut the length of the riser front and sides with a mitre or circular saw. Then mensurate the ascension or height of your footstep, and employ a tabular array saw to rip the width of the lath to fit underneath the top.
x. Shim the front and side risers into place and attach to the stoop framing with ii" trim head galvanized screws. We chose not to mitre cut the riser boards, so final but not least, nosotros touched upwardly the exposed cutting ends on the front riser lath with a bit of paint.
Have a really nifty DIY projection or tutorial that you want to share with others? Permit us know! We honey checking out what you're making these days, and learning from our readers. When you're ready, click hither to submit your projection and photos.
Source: https://www.apartmenttherapy.com/how-to-deck-over-an-ugly-cement-stoop-232910
Posted by: chambleefeativill.blogspot.com
0 Response to "How To Install Composite Decking Over Concrete Steps"
Post a Comment